It may also be due to a defective connection. Several instances of information on data positioning and location could not be found. Drive should be replaced. SMART also has parameter "Reallocation Event Count" for which wiki says the following; "Count of remap operations. http://birdsallgraphics.com/error-code/error-code-223-western-digital.php
The drive has not responded in the time allotted. Data sent between the host computer and the drive has been corrupted. At some point, however, the spare pool is exhausted, and no relocation nor remapping can take place. Check cabling & retest. http://superuser.com/questions/679260/western-digital-sector-relocation-error-code-226
Re-test Drive 159 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. This may be due to a defect with the drive or a bad connection. I wonder if there is a way to remap the problematic sectors? Search News Search Articles Jump To Article TTID# Microsoft KB Article # Hardware Manufacturers Software Manufacturers Search the Web Home | Software | Technical News | Reviews |
Is my teaching attitude wrong? Retest after checking the connections. Re-Test Drive 106 Track 0 Error Track 0 was not properly detected. better u urself go n get the supply.
The drive has not responded in the time allotted. The manufacture's message is basically a you have been warned sign. Retest. Replace Drive 225 Too Many Errors Found Error count reached a threshold value.
Replace the drive if the error repeats. Replace. I'd say keep after 'em until they give you one that works. can you do a long test?
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 46 00 00 00 40 Device Fault; Error: ABRT my site Re-test and Repair Option diagnostic utility 212 10+ Uncorr ECC Errors Error Correction Code (ECC) 10+. Replace Drive 223 Errors Repaired Errors found, but have been repaired successfully. You may need to rescan to ensure that the repairs were effective.
If ECC occurs, use Data Lifeguard repair option for additional error correction. have a peek at these guys Re-Test Drive 121 Servo Error Servo error. Re-test Drive 136 Bad Sector Sector Marked Bad Error. Check your connections and replace the cable.
Replace Drive 200 Drive Not Tested Supported WD drives are initialized with this status. Installing SATA Drivers without a Floppy Disk Creating bootable Windows 2000/XP/2003 Disc (Nero 6) Creating bootable Windows 2000/XP/2003 Disc (CDBurnerXP 3) Known Windows XP SP3 CD Labels Hard Drive Diagnostics Tools This may be due to a media error. check over here When this occurs, data loss will take place.
The drive has not responded back in the time allotted. Please re-test the drive with Data Lifeguard. The Identify Drive Command has not received an acceptable response from the drive.
S.M.A.R.T. i4004 01-06-2010 03:32 PM Re: wd diag error message try windows version (perhaps that old dos version is a dud for these new drives) http://support.wdc.com/product/downl...&sid=3&lang=en as they say: http://support.wdc.com/techinfo/gene...rcodes.asp#v28 "226 Sector ECC is a hardware correction technique that corrects errors. Test complete Defect Free 224 Errors not Repaired Errors found and have not been repaired.
It also may be due to a defective connection. ECC is a hardware correction technique that corrects errors. Re-test Drive 138 Still Busy Timeout Timeout from checking busy bit. http://birdsallgraphics.com/error-code/error-code-0007-western-digital.php This error can occur on non-Western Digital drives.
Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted. Self-Monitoring, Analysis, and Reporting Technology (SMART). Replace Drive 585 Busy Timeout During a read verify, a command could not be completed. RMA time.
The drive has not responded back in the time allotted. The time now is 10:47 AM. If an unstable sector is subsequently written or read successfully, this value is decreased and the sector is not remapped. You may need to rescan to ensure that the repairs were effective.
This may be due to a media or read/write error. Replace the drive if the error repeats. Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility. Check cabling & retest.
It also may be due to a defective connection.