Check connections and retest. Replace the drive. Replace Drive 584 Diag Command Error During a Quick Test, the sefl-test failed. EDIT2: Different drive worked, but had bootup problems. :X Last edited: Nov 10, 2010 Cerulean, Nov 10, 2010 Cerulean, Nov 10, 2010 #2 Nov 10, 2010 #3 drescherjm [H]ardForum Junkie http://birdsallgraphics.com/error-code/error-code-223-western-digital.php
Replace the drive if the error repeats. When I had a WD die to read element failure and then too many bad sectors and a smart error, it made it easy to RMA that drive. As you know I had this PC built by a local PC shop. Retest.
It also may be due to a defective connection. If Selective self-test is pending on power-up, resume after 0 minute delay. If ECC occurs, use Data Lifeguard for additional error correction. I could still move the mouse, but the interface would not respond to any clicks.
Re-Test Drive 109 DRQ WAS SET The drive did not properly respond to test commands. Return to WDC.com WD Community English Product Support My CloudMy BookMy PassportWD Elements & WD TVInternal DrivesWDLabsLegacy & Other Products Downloads WD Software Product Firmware Product Downloads Warranty & Returns Warranty Test complete Defect Free 224 Errors not Repaired Errors found and have not been repaired. Replace Drive 217 2-9 SERVO Errors SERVO 2-9.
The manufacture's message is basically a you have been warned sign. Replace Drive 209 Previous Error Code not found Data Lifeguard Diag could not determine a previous error code. Re-test 132 Command Error Command Aborted. It also may be due to a defective connection.
At some point, however, the spare pool is exhausted, and no relocation nor remapping can take place. Re-Test Drive 2 SMART Attribute Over Threshold Self-Monitoring, Analysis, and Reporting Technology (SMART) threshold exceeded condition. Smart status was reporting zero after the last time I ran dlgdiag in the other system, 3/4 of the way through chkdsk /r current pending sector count went back up to It also may be due to a defective connection.
Here are some examples of my tests: Note: I have a total of 3 Sata HD's - WD 1TB, Samsung 1TB, and WD 320GB(OS) -All 3 connected BOOTMGR is missing WD Replace the drive if the error repeats. Western Digital Error Code 0007 This may be due to a media error. Western Digital Error Codes The command set to be executed has timed out.
This may be due to a media or read/write error. have a peek at these guys Replace Drive 204 DRM Attribute too low after media scan. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 46 00 00 00 40 Device Fault; Error: ABRT Not the answer you're looking for?
is still reported. It also may be due to a defective connection. This may be an anomaly or a defect with the drive. check over here I am not aware of any problems running the PC.
Replace the drive if the error repeats. If ECC occurs, use Data Lifeguard repair option for additional error correction. General Purpose Logging supported.
Re-Test Drive 19 SMART Enabled Operation Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) Enable Operation failed. Re-test Drive 148 Not Selected Drive not selected. I backed up the contents of the drive to another system and booted up dlgdiag and did an extended test. It also may be due to a defective connection.
ECC is a hardware correction technique that corrects errors. The drive is toast, right? #1 lakedude, Dec 5, 2012 Fardringle Diamond Member Joined: Oct 23, 2000 Messages: 8,003 Likes Received: 6 Western Digital's Diagnostic Error Codes list says that Re-test Drive 206 Memory Allocation Error Unable to allocate memory for program structures. this content In other words, all of us, all of the time, are using partially defective disks.